LiYang Heat Pipe Solar Vacuum Tube

Borosilicate glass 3.3 full production,
safety and quality through ISO9002 certification
NEW Solar Vacuum Tube:
Process characteristics:
1. use of advanced production technology, professional production of various types of rough tube, vacuum glass tube
2. selective absorbing coating
3. high vacuum, high-performance collector
4. Low thermal loss coefficient
5. shock resistance, low temperature

Selection of advantages:
1. Glass selection of composite ISO3585: 1991 requirements borosilicate 3.3 glass, the glass has: strong acid, solar projection ratio, impact resistance and other advantages.
2. collector process by magnetron sputtering
3. deposition gradient selective absorbing coating (A1-N/A1), the coating on the Sun has a very high absorption rate and low emissivity, solar absorption ratio ≥ 0.92 (AM1.5), hemisphere than launch? h < 0.086 (80 °C ± 5 °C), air drying temperature of ts > 220 m
2
°C, gas pressure within the vacuum laminated P < 5 × 10-3pa, nausea amount of sun radiation exposure H ≤ 3.8MJ / m, the average heat loss coefficient ult ≤ 0.09w / (m °C).
4.25mm can withstand the impact of hail, even in cold winter areas can also be used.

material
borosilicate glass 3.3
length
1500mm
inner tube diameter
37mm
outer tube diameter
47mm
membrane
gradient AL-N-C/AL selective absorbing coating
solar absorptance
> 0.09 (AM = 1.5)(international requirements as:>0.86)
hemisphere emission ratio
> 0.086 (80 °C) (international provisions: ≤ 0.09)
air drying performance parameters
≥186square meters.°C/kw(international requirements as:≥175)
The amount of sun radiation exposure stuffy
≤ 2.86MJ / m
2
(international provisions: ≤ 3.8)
Average heat loss coefficient
≤ 0.75W / m (International provisions: ≤ 0.90)
inside and outside the tube laminated tube
≤ 5 × 10-3pa (international provisions: ≤ 5 × 10-2pa)
heat shock
Below 25°C 90°C repeated alternating hot and cold water more than three times without damaging the impact of
pressure
withstand the pressure of 0.6Mpa
anti-hail
size of not more than 25mm can withstand without damage hail attack

LiYang Solar Vacuum Tube

LiYang Solar Vacuum Tube:
Good economic environment;
three high vacuum tube; cost-effective;
environmental protection
LiYang Solar Vacuum Tube:
1. advanced: graded multi-layer magnetron sputtering of aluminum - nitrogen / aluminum coating solar selective absorption coating of new technology, the vacuum of not less than 1.33 × 10-3Pa, to further improve the efficiency of the vacuum tube collector.
2. timber stress: tube material selection consistent with QB/T2436-99 (idt) ISO4803-1978 standard of 3.3 Marino blank borosilicate glass tube manufacturing, its high transparency and good resistance to thermal shock , the optical stability of the strong.
3. Quality assurance: GB/T17049-1997 in strict accordance with national standards, meticulous organization, strict management of raw materials purchased from the beginning until the final product out of library staff work together strictly to the channel quality of products, To prevent unqualified products from



material
borosilicate glass 3.3
length
15-1800mm
inner tube diameter
37mm
outer tube diameter
47mm
membrane
gradient AL-N-C/AL selective absorbing coating
solar absorptance
> 0.09 (AM = 1.5)(international requirements as:>0.86)
hemisphere emission ratio
> 0.086 (80 °C) (international provisions: ≤ 0.09)
air drying performance parameters
≥186square meters.°C/kw(international requirements as:≥175)
The amount of sun radiation exposure stuffy
≤ 2.86MJ / m
2
(international provisions: ≤ 3.8)
Average heat loss coefficient
< 0.75W / m (International provisions: ≤ 0.90)
inside and outside the tube laminated tube
< 5 × 10-3pa (international provisions: ≤ 5 × 10-2pa)
heat shock
Below 25°C 90°C repeated alternating hot and cold water more than three times without damaging the impact of
pressure
withstand the pressure of 0.6Mpa
anti-hail
size of not more than 25mm can withstand without damage hail attack

LiYang Solar Vacuum Tube

LiYang Solar Vacuum Tube:
Good economic environment;
three high vacuum tube; cost-effective;
environmental protection
LiYang Solar Vacuum Tube:
1. advanced: graded multi-layer magnetron sputtering of aluminum - nitrogen / aluminum coating solar selective absorption coating of new technology, the vacuum of not less than 1.33 × 10-3Pa, to further improve the efficiency of the vacuum tube collector.
2. timber stress: tube material selection consistent with QB/T2436-99 (idt) ISO4803-1978 standard of 3.3 Marino blank borosilicate glass tube manufacturing, its high transparency and good resistance to thermal shock , the optical stability of the strong.
3. Quality assurance: GB/T17049-1997 in strict accordance with national standards, meticulous organization, strict management of raw materials purchased from the beginning until the final product out of library staff work together strictly to the channel quality of products, To prevent unqualified products from



material
borosilicate glass 3.3
length
15-1800mm
inner tube diameter
37mm
outer tube diameter
47mm
membrane
gradient AL-N-C/AL selective absorbing coating
solar absorptance
> 0.09 (AM = 1.5)(international requirements as:>0.86)
hemisphere emission ratio
> 0.086 (80 °C) (international provisions: ≤ 0.09)
air drying performance parameters
≥186square meters.°C/kw(international requirements as:≥175)
The amount of sun radiation exposure stuffy
≤ 2.86MJ / m
2
(international provisions: ≤ 3.8)
Average heat loss coefficient
< 0.75W / m (International provisions: ≤ 0.90)
inside and outside the tube laminated tube
< 5 × 10-3pa (international provisions: ≤ 5 × 10-2pa)
heat shock
Below 25°C 90°C repeated alternating hot and cold water more than three times without damaging the impact of
pressure
withstand the pressure of 0.6Mpa
anti-hail
size of not more than 25mm can withstand without damage hail attack

LiYang Solar-1 Vacuum Tube

LiYang Solar Vacuum Tube:
Good economic environment;
three high vacuum tube; cost-effective;
environmental protection
LiYang-1 Solar Vacuum Tube:
1. advanced: graded multi-layer magnetron sputtering of aluminum - nitrogen / aluminum coating solar selective absorption coating of new technology, the vacuum of not less than 1.33 × 10-3Pa, to further improve the efficiency of the vacuum tube collector.
2. timber stress: tube material selection consistent with QB/T2436-99 (idt) ISO4803-1978 standard of 3.3 Marino blank borosilicate glass tube manufacturing, its high transparency and good resistance to thermal shock , the optical stability of the strong.
3. Quality assurance: GB/T17049-1997 in strict accordance with national standards, meticulous organization, strict management of raw materials purchased from the beginning until the final product out of library staff work together strictly to the channel quality of products, To prevent unqualified products from



material
borosilicate glass 3.3
length
15-1800mm
inner tube diameter
37mm
outer tube diameter
47mm
membrane
gradient AL-N-C/AL selective absorbing coating
solar absorptance
> 0.09 (AM = 1.5)(international requirements as:>0.86)
hemisphere emission ratio
> 0.086 (80 °C) (international provisions: ≤ 0.09)
air drying performance parameters
≥186square meters.°C/kw(international requirements as:≥175)
The amount of sun radiation exposure stuffy
≤ 2.86MJ / m
2
(international provisions: ≤ 3.8)
Average heat loss coefficient
< 0.75W / m (International provisions: ≤ 0.90)
inside and outside the tube laminated tube
< 5 × 10-3pa (international provisions: ≤ 5 × 10-2pa)
heat shock
Below 25°C 90°C repeated alternating hot and cold water more than three times without damaging the impact of
pressure
withstand the pressure of 0.6Mpa
anti-hail
size of not more than 25mm can withstand without damage hail attack

LiYang new high quality Solar Vacuum Tubes

YangLiDe Solar Vacuum Tubes:
Good economic environment;
three high vacuum tube;
cost-effective;
YangLiDe Solar Vacuum Tubes:
Process characteristics:
1. use of advanced production technology, professional production of various types of rough tube, vacuum glass tube
2. selective absorbing coating
3. high vacuum, high-performance collector
4. Low thermal loss coefficient
5. shock resistance, low temperature
Selection of advantages:
1. Glass selection of composite ISO3585: 1991 requirements borosilicate 3.3 glass, the glass has: strong acid, solar projection ratio, impact resistance and other advantages.
2. collector process by magnetron sputtering
3. deposition gradient selective absorbing coating (A1-N/A1), the coating on the Sun has a very high absorption rate and low emissivity, solar absorption ratio ≥ 0.92 (AM1.5), hemisphere than launch? h ≤ 0.086 (80 °C ± 5 °C), air drying temperature of ts ≥ 220 m
2
°C, gas pressure within the vacuum laminated P ≤ 5 × 10-3pa, nausea amount of sun radiation exposure H ≤ 3.8MJ / m, the average heat loss coefficient ult ≤ 0.09w / (m °C).
4. 25mm can withstand the impact of hail, even in cold winter areas can also be used.

material
borosilicate glass 3.3
length
1500mm
inner tube diameter
37mm
outer tube diameter
47mm
membrane
gradient AL-N-C/AL selective absorbing coating
solar absorptance
> 0.09 (AM = 1.5)(international requirements as:>0.86)
hemisphere emission ratio
> 0.086 (80 °C) (international provisions: ≤ 0.09)
air drying performance parameters
≥186square meters.°C/kw(international requirements as:≥175)
The amount of sun radiation exposure stuffy
≤ 2.86MJ / m
2
(international provisions: ≤ 3.8)
Average heat loss coefficient
≤ 0.75W / m (International provisions: ≤ 0.90)
inside and outside the tube laminated tube
≤ 5 × 10-3pa (international provisions: ≤ 5 × 10-2pa)
heat shock
Below 25°C 90°C repeated alternating hot and cold water more than three times without damaging the impact of
pressure
withstand the pressure of 0.6Mpa
anti-hail
size of not more than 25mm can withstand without damage hail attack

LiYang-1 Aluminum alloy stents Solar water heater

Aluminum alloy stents Solar water heater
1.Solar heating tube:47*1.5m
2. nside material:304 stainless steel
Aluminum alloy stents Solar water heater
1.Solar heating tube:47*1.5m
2. inside material:304 stainless steel
3.insulation:50mm,60mmpolyurethane
4.outside material: Import choi, aluminium zinc plate
5.Scaffold materials: high aluminium zinc plate naisuanjian pensu


Features:
First, the high vacuum tube:
1, selection: 3.3 high borosilicate glass as raw material, its performance in line with ISO3585: 1991 requirements.
2, high thermal efficiency: use of space technology, 8-layer vacuum coating, vacuum layer of pure unadulterated, high vacuum and durable, the sun has a very high absorption rate and low thermal emittance.
3, the heat loss is small: between the layers in the vacuum tube to maintain a high vacuum to minimize heat conduction, convection heat loss.
4, long life: stable coating layer, not aging, fading, material selection, production, transportation, quality and other aspects of procedure strictly, longer life.
5, corrosion resistance: A new anti-corrosion technology to effectively inhibit microbial breeding, excellent resistance to chemical attack, for a variety of water quality.
6, anti-cold: cold even in the high latitudes of the northeastern region, cold cold, you can still use hot water, shows the rate of super-collector.
7, strength: 25mm hail impact without damage.
Second, the water tank:
1. Antiseptic tank, longer life: using quality SUS304-2B food grade stainless steel plate, after the automatic welding process handling, interior and stronger, and better sealing performance, never leakage, bladder using patented technology can effectively prevent scale adhesion, super anti-corrosion, water is more clean, in line with national drinking water standards and longer life.
2. "Deducted" process: the first use of inner alchemy between the thunder and the inner alchemy "press button" process, to avoid changes due to welding of stainless steel materials to ensure that the liner will never leak, while the process to ensure that the water tank liner seamless with the side cover, the overall rounded appearance.
360 ° full three-dimensional thermal insulation technology, extra-thick insulation, hot water is more durable: thick polyurethane insulation layer: use of environmentally friendly high-density polyurethane insulation materials, the overall high-pressure foam molding, high temperature heat treatment technology, closed Hole 98%, insulation thickness of 50 mm or more, does not ensure that the heat transfer and dissipation in the air, the effective attenuation against temperature, heat loss rate is extremely small, even in the cold winter, but also to achieve excellent thermal insulation effect.
Third, the bracket:
1. Attractive appearance, fashion, fashion: The thicker aluminum, wind streamline design, anti-oxidation treatment, durable corrosion-resistant, nice.
More capable against wind and snow, the whole rugged: optimal "bridge type" connection combination stent, the mechanical capacity of humanity and perfect in one, non-reflective board design, supports a more stable wind, and dust and reflectors to overcome the winter shortcomings affecting the thermal efficiency of snow, the whole rock solid, anti-hail performance characteristics:
Second, efficient vacuum tube:
8, selection: 3.3 high borosilicate glass as raw material, its performance in line with ISO3585: 1991 requirements.
9, high thermal efficiency: use of space technology, 8-layer vacuum coating, vacuum layer of pure unadulterated, high vacuum and durable, the sun has a very high absorption rate and low thermal emittance.
10, the heat loss is small: between the layers in the vacuum tube to maintain a high vacuum to minimize heat conduction, convection heat loss.
11, long life: stable coating layer, not aging, fading, material selection, production, transportation, quality and other aspects of procedure strictly, longer life.
12, anti-corrosion: A new anti-corrosion technology to effectively inhibit microbial breeding, excellent resistance to chemical attack, for a variety of water quality.
13, anti-cold: cold even in the high latitudes of the northeastern region, cold cold, you can still use hot water, shows the rate of super-collector.
14, strength: 25mm hail impact without damage.

Modle
solar vacuum tube
scaffold
tank
length
diameter
angle
case material
insulation material
liner material
capacity
LY47-1520-45
1500mm
47mm
45
Imports of high quality stainless steel bend frame
Imports of stainless steel
5mm-65mm imported polyurethane foam
SUS304-2B imported food grade stainless steel plate
140L

LiYang-1 Blue Solar Vacuum Tube

1.Standard 3.3 high-boron-silicon glass-pipe
2.Low coefficient of heat loss
3.Good performance & price
4.15years warranty.
Solar Vacuum Tube:
Selection of advantages:
1. Glass selection of composite ISO3585: 1991 requirements borosilicate 3.3 glass, the glass has: strong acid, solar projection ratio, impact resistance and other advantages.
2. collector process by magnetron sputtering
3. deposition gradient selective absorbing coating (A1-N/A1), the coating on the Sun has a very high absorption rate and low emissivity, solar absorption ratio ≥ 0.92 (AM1.5), hemisphere than launch? h ≤ 0.086 (80 °C ± 5 °C), air drying temperature of ts ≥ 220 m
2
°C, gas pressure within the vacuum laminated P < 5 × 10-3pa, nausea amount of sun radiation exposure H ≤ 3.8MJ / m, the average heat loss coefficient ult ≤ 0.09w / (m °C).
4.25mm can withstand the impact of hail, even in cold winter areas can also be used.


material
borosilicate glass 3.3
length
1600mm
inner tube diameter
37mm
outer tube diameter
47mm
membrane
gradient AL-N-C/AL selective absorbing coating
solar absorptance
> 0.09 (AM = 1.5)(international requirements as:>0.86)
hemisphere emission ratio
> 0.086 (80 °C) (international provisions: ≤ 0.09)
air drying performance parameters
≥186square meters.°C/kw(international requirements as:≥175)
The amount of sun radiation exposure stuffy
≤ 2.86MJ / m
2
(international provisions: ≤ 3.8)
Average heat loss coefficient
≤ 0.75W / m (International provisions: ≤ 0.90)
inside and outside the tube laminated tube
≤ 5 × 10-3pa (international provisions: ≤ 5 × 10-2pa)
heat shock
Below 25°C 90°C repeated alternating hot and cold water more than three times without damaging the impact of
pressure
withstand the pressure of 0.6Mpa
anti-hail
size of not more than 25mm can withstand without damage hail attack

2011 DYAN Improved Biomass Briquetting Press Machine for Biomass Briquettes

Wood Briquette Machine:
1.High production, energy-saving
2.Long durablity,good output
3.Easy to operate
4.Stable performance
2011 DYAN Improved Biomass Briquetting Press Machine for Biomass Briquettes

Biomass Briquette Machine
make the biomass material into briquettes. After the well preparement of raw metarial, briquetting is easy at right operation of biomass briquette press. When machine rise to over 300 centigrade, the material can be feeding continuously into briquetting press. First, the color of briquettes may be a little dark even black, but after a while, the color will be light to normal level coming out of biomass briquette machine.
Appropriate Biomass Residues for Briquetting:

1. Effect of particle size and shape of the agro residues for densification. The ideal size was identified to be 3-5mm.
2. Effect of moisture. Ideal level was 8 to 12 per cent.
3. Effect of feed preheating studied and the temperature upto 90 to 110 degree centigrade for the feed was optimised.
4. Effect of temperature on the die was found important and the temperature at 280 to 290 0C was observed to be most appropriate
5. Effect of mixing rice husk with bagasse and bagasse pith to achieve the briquetting of these materials

Working Principle of Sawdust Briquette Machine:

Sawdust Briquette machine uses a large screw to grind, compress and extrude the biomass into briquettes. The natural lignin content in biomass is liberated with wood fiber under high pressure and temperature.In the briquetting process lignin serves as the glue and combines the particles of wood together,thus binding, compressing the biomass to form into various moulds of high density briquette, such as hexagonal,quadrangular, square,etc. As your requirement, we can also change the shape to order. And the diameter of briquettes are from 50-80 mm. Moreover non-binder needs to be used during this process.
The process for producing charcoal briquette as follow:

1. Crush the raw material into small pieces (diameter is about 3-5mm)
2. Dry the material by machine or dried it in the sun , till the moisture is less than 12%
3. Put the material into feed let of briquette machine
4. Produce the briquette stick from biomass material without any additive
4. Carbonized the briquette stick
Characteristic of Biomass Briquette Machine:

1. No binder or noxious chemical need to use.
2. The humidity of the raw materials is controlled in 8-12%.
3. Using the advanced Hot air drying system with the perfect performance.
4. After the processing of High temperature, purification, smoke removing, the carbonizing equipment transforms the semi-finished bio-fuel briquette into a smoke-free, tasteless, non-toxic cleaning carbon.

Advantages of biomass briquettes:
♦ Increase the net calorific value per unit volume after biomass briquetting
♦ Easy to transport and store as densified product
♦ Better solution to the problem of residue disposal
♦Uniform in size and quality as a kind of biofuel briquette
♦ Reduce excess deforestation by providing a substitute for fuel wood

Biomass Briquette Machine:

LiYang-3 Aluminum alloy stents Solar water heater

Aluminum alloy stents Solar water heater
1.Solar heating tube:58*1.8m
2. nside material:304 stainless steel
Aluminum alloy stents Solar water heater
1.Solar heating tube:58*1.8m
2. inside material:304 stainless steel
3.insulation:50mm,60mmpolyurethane
4.outside material: Import choi, aluminium zinc plate
5.Scaffold materials: high aluminium zinc plate naisuanjian pensu


Features:
First, the high vacuum tube:
1, selection: 3.3 high borosilicate glass as raw material, its performance in line with ISO3585: 1991 requirements.
2, high thermal efficiency: use of space technology, 8-layer vacuum coating, vacuum layer of pure unadulterated, high vacuum and durable, the sun has a very high absorption rate and low thermal emittance.
3, the heat loss is small: between the layers in the vacuum tube to maintain a high vacuum to minimize heat conduction, convection heat loss.
4, long life: stable coating layer, not aging, fading, material selection, production, transportation, quality and other aspects of procedure strictly, longer life.
5, corrosion resistance: A new anti-corrosion technology to effectively inhibit microbial breeding, excellent resistance to chemical attack, for a variety of water quality.
6, anti-cold: cold even in the high latitudes of the northeastern region, cold cold, you can still use hot water, shows the rate of super-collector.
7, strength: 25mm hail impact without damage.
Second, the water tank:
1. Antiseptic tank, longer life: using quality SUS304-2B food grade stainless steel plate, after the automatic welding process handling, interior and stronger, and better sealing performance, never leakage, bladder using patented technology can effectively prevent scale adhesion, super anti-corrosion, water is more clean, in line with national drinking water standards and longer life.
2. "Deducted" process: the first use of inner alchemy between the thunder and the inner alchemy "press button" process, to avoid changes due to welding of stainless steel materials to ensure that the liner will never leak, while the process to ensure that the water tank liner seamless with the side cover, the overall rounded appearance.
360 ° full three-dimensional thermal insulation technology, extra-thick insulation, hot water is more durable: thick polyurethane insulation layer: use of environmentally friendly high-density polyurethane insulation materials, the overall high-pressure foam molding, high temperature heat treatment technology, closed Hole 98%, insulation thickness of 50 mm or more, does not ensure that the heat transfer and dissipation in the air, the effective attenuation against temperature, heat loss rate is extremely small, even in the cold winter, but also to achieve excellent thermal insulation effect.
Third, the bracket:
1. Attractive appearance, fashion, fashion: The thicker aluminum, wind streamline design, anti-oxidation treatment, durable corrosion-resistant, nice.
More capable against wind and snow, the whole rugged: optimal "bridge type" connection combination stent, the mechanical capacity of humanity and perfect in one, non-reflective board design, supports a more stable wind, and dust and reflectors to overcome the winter shortcomings affecting the thermal efficiency of snow, the whole rock solid, anti-hail performance characteristics:
Second, efficient vacuum tube:
8, selection: 3.3 high borosilicate glass as raw material, its performance in line with ISO3585: 1991 requirements.
9, high thermal efficiency: use of space technology, 8-layer vacuum coating, vacuum layer of pure unadulterated, high vacuum and durable, the sun has a very high absorption rate and low thermal emittance.
10, the heat loss is small: between the layers in the vacuum tube to maintain a high vacuum to minimize heat conduction, convection heat loss.
11, long life: stable coating layer, not aging, fading, material selection, production, transportation, quality and other aspects of procedure strictly, longer life.
12, anti-corrosion: A new anti-corrosion technology to effectively inhibit microbial breeding, excellent resistance to chemical attack, for a variety of water quality.
13, anti-cold: cold even in the high latitudes of the northeastern region, cold cold, you can still use hot water, shows the rate of super-collector.
14, strength: 25mm hail impact without damage.

Modle
solar vacuum tube
scaffold
tank
length
diameter
angle
case material
insulation material
liner material
capacity
LY58-1814-45
1800mm
58mm
45
Imports of high quality stainless steel bend frame
Imports of stainless steel
5mm-65mm imported polyurethane foam
SUS304-2B imported food grade stainless steel plate
160L

LiYang-3 Solar Vacuum Tube

LiYang Solar Vacuum Tube:
1) high quality and reasonable price
2) environmental friendly
3) nice design
4) ISO9001:2000..
LiYang Solar Vacuum Tube:
1. advanced: graded multi-layer magnetron sputtering of aluminum - nitrogen / aluminum coating solar selective absorption coating of new technology, the vacuum of not less than 1.33 × 10-3Pa, to further improve the efficiency of the vacuum tube collector.
2. timber stress: tube material selection consistent with QB/T2436-99 (idt) ISO4803-1978 standard of 3.3 Marino blank borosilicate glass tube manufacturing, its high transparency and good resistance to thermal shock , the optical stability of the strong.
3. Quality assurance: GB/T17049-1997 in strict accordance with national standards, meticulous organization, strict management of raw materials purchased from the beginning until the final product out of library staff work together strictly to the channel quality of products, To prevent unqualified products from



material
borosilicate glass 3.3
length
1800mm
inner tube diameter
47mm
outer tube diameter
58mm
membrane
gradient AL-N-C/AL selective absorbing coating
solar absorptance
> 0.09 (AM = 1.5)(international requirements as:>0.86)
hemisphere emission ratio
> 0.086 (80 °C) (international provisions: ≤ 0.09)
air drying performance parameters
≥186square meters.°C/kw(international requirements as:≥175)
The amount of sun radiation exposure stuffy
< 2.86MJ / m
2
(international provisions: ≤ 3.8)
Average heat loss coefficient
< 0.75W / m (International provisions: ≤ 0.90)
inside and outside the tube laminated tube
< 5 × 10-3pa (international provisions: ≤ 5 × 10-2pa)
heat shock
Below 25°C 90°C repeated alternating hot and cold water more than three times without damaging the impact of
pressure
withstand the pressure of 0.6Mpa
anti-hail
size of not more than 25mm can withstand without damage hail attack

LiYang-3 new high quality Solar Vacuum Tubes

LiYang Solar Vacuum Tube:
Good economic environment;
three high vacuum tube;
cost-effective;
LiYang-3 Solar Vacuum Tube:
1. advanced: graded multi-layer magnetron sputtering of aluminum - nitrogen / aluminum coating solar selective absorption coating of new technology, the vacuum of not less than 1.33 × 10-3Pa, to further improve the efficiency of the vacuum tube collector.
2. timber stress: tube material selection consistent with QB/T2436-99 (idt) ISO4803-1978 standard of 3.3 Marino blank borosilicate glass tube manufacturing, its high transparency and good resistance to thermal shock , the optical stability of the strong.
3. Quality assurance: GB/T17049-1997 in strict accordance with national standards, meticulous organization, strict management of raw materials purchased from the beginning until the final product out of library staff work together strictly to the channel quality of products, To prevent unqualified products from



material
borosilicate glass 3.3
length
1500mm
inner tube diameter
47mm
outer tube diameter
58mm
membrane
gradient AL-N-C/AL selective absorbing coating
solar absorptance
> 0.09 (AM = 1.5)(international requirements as:>0.86)
hemisphere emission ratio
> 0.086 (80 °C) (international provisions: ≤ 0.09)
air drying performance parameters
≥186square meters.°C/kw(international requirements as:≥175)
The amount of sun radiation exposure stuffy
≤ 2.86MJ / m
2
(international provisions: ≤ 3.8)
Average heat loss coefficient
≤ 0.75W / m (International provisions: ≤ 0.90)
inside and outside the tube laminated tube
≤ 5 × 10-3pa (international provisions: ≤ 5 × 10-2pa)
heat shock
Below 25°C 90°C repeated alternating hot and cold water more than three times without damaging the impact of
pressure
withstand the pressure of 0.6Mpa
anti-hail
size of not more than 25mm can withstand without damage hail attack

LiYang-4 Heat Pipe Solar Vacuum Tube

liyang solar vacuum
1,Made from Pyrex glass 3.3
2,Performance in line with ISO3585: 1991 requirements
3,High thermal effic
solar vacuum tube:

Selection of advantages:
1. Glass selection of composite ISO3585: 1991 requirements borosilicate 3.3 glass, the glass has: strong acid, solar projection ratio, impact resistance and other advantages.
2. collector process by magnetron sputtering
3. deposition gradient selective absorbing coating (A1-N/A1), the coating on the Sun has a very high absorption rate and low emissivity, solar absorption ratio > 0.92 (AM1.5), hemisphere than launch? h < 0.086 (80 °C ± 5 °C), air drying temperature of ts > 220 m
2
°C, gas pressure within the vacuum laminated P < 5 × 10-3pa, nausea amount of sun radiation exposure H < 3.8MJ / m, the average heat loss coefficient ult < 0.09w / (m °C).
4.25mm can withstand the impact of hail, even in cold winter areas can also be used.


material
borosilicate glass 3.3
length
1600mm
inner tube diameter
47mm
outer tube diameter
58mm
membrane
gradient AL-N-C/AL selective absorbing coating
solar absorptance
> 0.09 (AM = 1.5)(international requirements as:>0.86)
hemisphere emission ratio
> 0.086 (80 °C) (international provisions: ≤ 0.09)
air drying performance parameters
≥186square meters.°C/kw(international requirements as:≥175)
The amount of sun radiation exposure stuffy
< 2.86MJ / m
2
(international provisions: ≤ 3.8)
Average heat loss coefficient
≤ 0.75W / m (International provisions: ≤ 0.90)
inside and outside the tube laminated tube
≤ 5 × 10-3pa (international provisions: ≤ 5 × 10-2pa)
heat shock
Below 25°C 90°C repeated alternating hot and cold water more than three times without damaging the impact of
pressure
withstand the pressure of 0.6Mpa
anti-hail
size of not more than 25mm can withstand without damage hail attack

LiYang-4 Solar Vacuum Tube

LiYang Solar Vacuum Tube:
1) high quality and reasonable price
2) environmental friendly
3) nice design
4) ISO9001:2000..
LiYang Solar Vacuum Tube:
1. advanced: graded multi-layer magnetron sputtering of aluminum - nitrogen / aluminum coating solar selective absorption coating of new technology, the vacuum of not less than 1.33 × 10-3Pa, to further improve the efficiency of the vacuum tube collector.
2. timber stress: tube material selection consistent with QB/T2436-99 (idt) ISO4803-1978 standard of 3.3 Marino blank borosilicate glass tube manufacturing, its high transparency and good resistance to thermal shock , the optical stability of the strong.
3. Quality assurance: GB/T17049-1997 in strict accordance with national standards, meticulous organization, strict management of raw materials purchased from the beginning until the final product out of library staff work together strictly to the channel quality of products, To prevent unqualified products from



material
borosilicate glass 3.3
length
1500mm
inner tube diameter
47mm
outer tube diameter
58mm
membrane
gradient AL-N-C/AL selective absorbing coating
solar absorptance
> 0.09 (AM = 1.5)(international requirements as:>0.86)
hemisphere emission ratio
> 0.086 (80 °C) (international provisions: ≤ 0.09)
air drying performance parameters
≥186square meters.°C/kw(international requirements as:≥175)
The amount of sun radiation exposure stuffy
< 2.86MJ / m
2
(international provisions: ≤ 3.8)
Average heat loss coefficient
< 0.75W / m (International provisions: ≤ 0.90)
inside and outside the tube laminated tube
< 5 × 10-3pa (international provisions: ≤ 5 × 10-2pa)
heat shock
Below 25°C 90°C repeated alternating hot and cold water more than three times without damaging the impact of
pressure
withstand the pressure of 0.6Mpa
anti-hail
size of not more than 25mm can withstand without damage hail attack

LiYang-4 Three Target Purple Gold Vacuum Tube

LiYang Solar Vacuum Tube:
1) high quality and reasonable price
2) environmental friendly
3) nice design
4) ISO9001:2000..
LiYang Solar Vacuum Tube:
1. advanced: graded multi-layer magnetron sputtering of aluminum - nitrogen / aluminum coating solar selective absorption coating of new technology, the vacuum of not less than 1.33 × 10-3Pa, to further improve the efficiency of the vacuum tube collector.
2. timber stress: tube material selection consistent with QB/T2436-99 (idt) ISO4803-1978 standard of 3.3 Marino blank borosilicate glass tube manufacturing, its high transparency and good resistance to thermal shock , the optical stability of the strong.
3. Quality assurance: GB/T17049-1997 in strict accordance with national standards, meticulous organization, strict management of raw materials purchased from the beginning until the final product out of library staff work together strictly to the channel quality of products, To prevent unqualified products from



material
borosilicate glass 3.3
length
1800mm
inner tube diameter
47mm
outer tube diameter
58mm
membrane
gradient AL-N-C/AL selective absorbing coating
solar absorptance
> 0.09 (AM = 1.5)(international requirements as:>0.86)
hemisphere emission ratio
> 0.086 (80 °C) (international provisions: ≤ 0.09)
air drying performance parameters
≥186square meters.°C/kw(international requirements as:≥175)
The amount of sun radiation exposure stuffy
< 2.86MJ / m
2
(international provisions: ≤ 3.8)
Average heat loss coefficient
< 0.75W / m (International provisions: ≤ 0.90)
inside and outside the tube laminated tube
< 5 × 10-3pa (international provisions: ≤ 5 × 10-2pa)
heat shock
Below 25°C 90°C repeated alternating hot and cold water more than three times without damaging the impact of
pressure
withstand the pressure of 0.6Mpa
anti-hail
size of not more than 25mm can withstand without damage hail attack

LiYang-4 new high quality Solar Vacuum Tube

LiYang Solar Vacuum Tube:
Good economic environment;
three high vacuum tube;
cost-effective;
LiYang-4 Solar Vacuum Tube:
1. advanced: graded multi-layer magnetron sputtering of aluminum - nitrogen / aluminum coating solar selective absorption coating of new technology, the vacuum of not less than 1.33 × 10-3Pa, to further improve the efficiency of the vacuum tube collector.
2. timber stress: tube material selection consistent with QB/T2436-99 (idt) ISO4803-1978 standard of 3.3 Marino blank borosilicate glass tube manufacturing, its high transparency and good resistance to thermal shock , the optical stability of the strong.
3. Quality assurance: GB/T17049-1997 in strict accordance with national standards, meticulous organization, strict management of raw materials purchased from the beginning until the final product out of library staff work together strictly to the channel quality of products, To prevent unqualified products from



material
borosilicate glass 3.3
length
1600mm
inner tube diameter
47mm
outer tube diameter
58mm
membrane
gradient AL-N-C/AL selective absorbing coating
solar absorptance
> 0.09 (AM = 1.5)(international requirements as:>0.86)
hemisphere emission ratio
> 0.086 (80 °C) (international provisions: ≤ 0.09)
air drying performance parameters
≥186square meters.°C/kw(international requirements as:≥175)
The amount of sun radiation exposure stuffy
≤ 2.86MJ / m
2
(international provisions: ≤ 3.8)
Average heat loss coefficient
≤ 0.75W / m (International provisions: ≤ 0.90)
inside and outside the tube laminated tube
≤ 5 × 10-3pa (international provisions: ≤ 5 × 10-2pa)
heat shock
Below 25°C 90°C repeated alternating hot and cold water more than three times without damaging the impact of
pressure
withstand the pressure of 0.6Mpa
anti-hail
size of not more than 25mm can withstand without damage hail attack

LiYang-5 Blue Solar Vacuum Tube

.High efficiency,high quality.
2.ensure operation in winter
3.15years' warranty for tube...
Solar Vacuum Tube:
Selection of advantages:
1. Glass selection of composite ISO3585: 1991 requirements borosilicate 3.3 glass, the glass has: strong acid, solar projection ratio, impact resistance and other advantages.
2. collector process by magnetron sputtering
3. deposition gradient selective absorbing coating (A1-N/A1), the coating on the Sun has a very high absorption rate and low emissivity, solar absorption ratio ≥ 0.92 (AM1.5), hemisphere than launch? h < 0.086 (80 °C ± 5 °C), air drying temperature of ts > 220 m
2
°C, gas pressure within the vacuum laminated P < 5 × 10-3pa, nausea amount of sun radiation exposure H ≤ 3.8MJ / m, the average heat loss coefficient ult < 0.09w / (m °C).
4.25mm can withstand the impact of hail, even in cold winter areas can also be used.


material
borosilicate glass 3.3
length
1800mm
inner tube diameter
47mm
outer tube diameter
58mm
membrane
gradient AL-N-C/AL selective absorbing coating
solar absorptance
> 0.09 (AM = 1.5)(international requirements as:>0.86)
hemisphere emission ratio
> 0.086 (80 °C) (international provisions: ≤ 0.09)
air drying performance parameters
≥186square meters.°C/kw(international requirements as:≥175)
The amount of sun radiation exposure stuffy
≤ 2.86MJ / m
2
(international provisions: ≤ 3.8)
Average heat loss coefficient
≤ 0.75W / m (International provisions: ≤ 0.90)
inside and outside the tube laminated tube
≤ 5 × 10-3pa (international provisions: ≤ 5 × 10-2pa)
heat shock
Below 25°C 90°C repeated alternating hot and cold water more than three times without damaging the impact of
pressure
withstand the pressure of 0.6Mpa
anti-hail
size of not more than 25mm can withstand without damage hail attack

LiYang-5 Heat Pipe Solar Vacuum Tube

LiYang Solar Vacuum Tube:Natural, environmentally friendly, high quality, light, stylish
LiYang-5 Solar Vacuum Tube:


1. Advanced technology: The multi-layer magnetron sputtering gradation Al - N / aluminum coating solar selective absorption coating of new technology, the vacuum of not less than 1.33 × 10-3Pa, to further improve the efficiency of the vacuum tube collector.
2. with material about: tube material selection consistent with QB/T2436-99 (idt) ISO4803-1978 standard of 3.3 Marino blank borosilicate glass tube manufacturing, its high transparency and good resistance to thermal shock, high optical stability.
3. Quality assurance: in strict accordance with GB/T17049-1997 national standards, meticulous organization, strict management of raw materials purchased from the beginning until the final product out of library co-operation of all staff, strict product quality to the road to eliminate substandard products out of
4. Specifications: The current production of a Φ47, Φ58, Φ70 diameter, 1.2 m / 1.5 m / 1.6 m / 1.8 m /


material
borosilicate glass 3.3
length
1500mm
inner tube diameter
37mm
outer tube diameter
47mm
membrane
gradient AL-N-C/AL selective absorbing coating
solar absorptance
> 0.09 (AM = 1.5)(international requirements as:>0.86)
hemisphere emission ratio
> 0.086 (80 °C) (international provisions: ≤ 0.09)
air drying performance parameters
≥186square meters.°C/kw(international requirements as:≥175)
The amount of sun radiation exposure stuffy
≤ 2.86MJ / m
2
(international provisions: ≤ 3.8)
Average heat loss coefficient
≤ 0.75W / m (International provisions: ≤ 0.90)
inside and outside the tube laminated tube
≤ 5 × 10-3pa (international provisions: ≤ 5 × 10-2pa)
heat shock
Below 25°C 90°C repeated alternating hot and cold water more than three times without damaging the impact of
pressure
withstand the pressure of 0.6Mpa
anti-hail
size of not more than 25mm can withstand without damage hail attack

LiYang-5 Solar Vacuum Tube

LiYang Solar Vacuum Tube:
1) high quality and reasonable price
2) environmental friendly
3) nice design
4) ISO9001:2000..
LiYang Solar Vacuum Tube:
1. advanced: graded multi-layer magnetron sputtering of aluminum - nitrogen / aluminum coating solar selective absorption coating of new technology, the vacuum of not less than 1.33 × 10-3Pa, to further improve the efficiency of the vacuum tube collector.
2. timber stress: tube material selection consistent with QB/T2436-99 (idt) ISO4803-1978 standard of 3.3 Marino blank borosilicate glass tube manufacturing, its high transparency and good resistance to thermal shock , the optical stability of the strong.
3. Quality assurance: GB/T17049-1997 in strict accordance with national standards, meticulous organization, strict management of raw materials purchased from the beginning until the final product out of library staff work together strictly to the channel quality of products, To prevent unqualified products from



material
borosilicate glass 3.3
length
1600mm
inner tube diameter
47mm
outer tube diameter
58mm
membrane
gradient AL-N-C/AL selective absorbing coating
solar absorptance
> 0.09 (AM = 1.5)(international requirements as:>0.86)
hemisphere emission ratio
> 0.086 (80 °C) (international provisions: ≤ 0.09)
air drying performance parameters
≥186square meters.°C/kw(international requirements as:≥175)
The amount of sun radiation exposure stuffy
< 2.86MJ / m
2
(international provisions: ≤ 3.8)
Average heat loss coefficient
< 0.75W / m (International provisions: ≤ 0.90)
inside and outside the tube laminated tube
< 5 × 10-3pa (international provisions: ≤ 5 × 10-2pa)
heat shock
Below 25°C 90°C repeated alternating hot and cold water more than three times without damaging the impact of
pressure
withstand the pressure of 0.6Mpa
anti-hail
size of not more than 25mm can withstand without damage hail attack

2011 DYAN Improved Energy Efficient Biomass Briquetting Press Machine(86-371-60328000)

Wood Briquette Machine:
1.High production, energy-saving
2.Long durablity,good output
3.Easy to operate
4.Stable performance
2011 DYAN Improved Energy Efficient Biomass Briquetting Press Machine

Biomass Briquette Machine
make the biomass material into briquettes. After the well preparement of raw metarial, briquetting is easy at right operation of biomass briquette press. When machine rise to over 300 centigrade, the material can be feeding continuously into briquetting press. First, the color of briquettes may be a little dark even black, but after a while, the color will be light to normal level coming out of biomass briquette machine.
Appropriate Biomass Residues for Briquetting:

1. Effect of particle size and shape of the agro residues for densification. The ideal size was identified to be 3-5mm.
2. Effect of moisture. Ideal level was 8 to 12 per cent.
3. Effect of feed preheating studied and the temperature upto 90 to 110 degree centigrade for the feed was optimised.
4. Effect of temperature on the die was found important and the temperature at 280 to 290 0C was observed to be most appropriate
5. Effect of mixing rice husk with bagasse and bagasse pith to achieve the briquetting of these materials

Working Principle of Sawdust Briquette Machine:

Sawdust Briquette machine uses a large screw to grind, compress and extrude the biomass into briquettes. The natural lignin content in biomass is liberated with wood fiber under high pressure and temperature.In the briquetting process lignin serves as the glue and combines the particles of wood together,thus binding, compressing the biomass to form into various moulds of high density briquette, such as hexagonal,quadrangular, square,etc. As your requirement, we can also change the shape to order. And the diameter of briquettes are from 50-80 mm. Moreover non-binder needs to be used during this process.
The process for producing charcoal briquette as follow:

1. Crush the raw material into small pieces (diameter is about 3-5mm)
2. Dry the material by machine or dried it in the sun , till the moisture is less than 12%
3. Put the material into feed let of briquette machine
4. Produce the briquette stick from biomass material without any additive
4. Carbonized the briquette stick
Characteristic of Biomass Briquette Machine:

1. No binder or noxious chemical need to use.
2. The humidity of the raw materials is controlled in 8-12%.
3. Using the advanced Hot air drying system with the perfect performance.
4. After the processing of High temperature, purification, smoke removing, the carbonizing equipment transforms the semi-finished bio-fuel briquette into a smoke-free, tasteless, non-toxic cleaning carbon.

Advantages of biomass briquettes:
♦ Increase the net calorific value per unit volume after biomass briquetting
♦ Easy to transport and store as densified product
♦ Better solution to the problem of residue disposal
♦Uniform in size and quality as a kind of biofuel briquette
♦ Reduce excess deforestation by providing a substitute for fuel wood

Biomass Briquette Machine:

LiYang-6 Blue Vacuum Tube

1) high quality and reasonable price
2) environmental friendly
3) nice design
4) ISO9001:2000...
Solar Vacuum Tube:
1. advanced: graded multi-layer magnetron sputtering of aluminum - nitrogen / aluminum coating solar selective absorption coating of new technology, the vacuum of not less than 1.33 × 10-3Pa, to further improve the efficiency of the vacuum tube collector.
2. timber stress: tube material selection consistent with QB/T2436-99 (idt) ISO4803-1978 standard of 3.3 Marino blank borosilicate glass tube manufacturing, its high transparency and good resistance to thermal shock , the optical stability of the strong.
3. Quality assurance: GB/T17049-1997 in strict accordance with national standards, meticulous organization, strict management of raw materials purchased from the beginning until the final product out of library staff work together strictly to the channel quality of products, To prevent unqualified products from



material
borosilicate glass 3.3
length
2000mm
inner tube diameter
37mm
outer tube diameter
47mm
membrane
gradient AL-N-C/AL selective absorbing coating
solar absorptance
> 0.09 (AM = 1.5)(international requirements as:>0.86)
hemisphere emission ratio
> 0.086 (80 °C) (international provisions: ≤ 0.09)
air drying performance parameters
≥186square meters.°C/kw(international requirements as:≥175)
The amount of sun radiation exposure stuffy
≤ 2.86MJ / m
2
(international provisions: ≤ 3.8)
Average heat loss coefficient
< 0.75W / m (International provisions: ≤ 0.90)
inside and outside the tube laminated tube
≤ 5 × 10-3pa (international provisions: ≤ 5 × 10-2pa)
heat shock
Below 25°C 90°C repeated alternating hot and cold water more than three times without damaging the impact of
pressure
withstand the pressure of 0.6Mpa
anti-hail
size of not more than 25mm can withstand without damage hail attack

LiYang-B Unpressurized Solar Water Heater:

1)ce&solarkeymark&ccc for solar collector
2)15 years warranty
3)easy installation, adjustable bracket
4)Best price
Solar Water Heater:
Modle
solar vacuum tube
scaffold
water tank
for the family
length
diameter
angle
case material
Insulation materials
interior materials
capacity
ly47-1524-45
1500mm
47mm
45
Aluminum Bracket
Imports of pearl plate corrosion, galvanized steel
Polyurethane
SUS304-2B food grade stainless steel
160L
2-3



features:
1. thermal efficiency: Forbidden three high vacuum tube of thermal efficiency than the average increased by 15% -25%.
2. Anti-cold: suitable for use in the cold, hard winter frost crack. Minus 40 degrees without freezing.
3. water quality is good: to avoid the metal coating on the water quality caused by direct contamination.
4. does not scale: do not clean up the scale, heat-absorbing effect over a decade.
5. not bombing: Even in 300 degree heat, they will not be bombing.

LiYang-C Unpressurized Solar Water Heater:

1,It is high efficient,stable performance.
2,widely used in domestic hot water system.
3,Soalr Keymark,SRCC...
Solar Water Heater:
Modle
solar vacuum tube
scaffold
water tank
for the family
length
diameter
angle
case material
Insulation materials
interior materials
capacity
ly58-1814-45
1800mm
47mm
45
Aluminum Bracket
Imports of pearl plate corrosion, galvanized steel
Polyurethane
SUS304-2B food grade stainless steel
130L
2-3



Features:
1. thermal efficiency: Forbidden three high vacuum tube of thermal efficiency than the average increased by 15% -25%.
2. Anti-cold: suitable for use in the cold, hard winter frost crack. Minus 40 degrees without freezing.
3. water quality is good: to avoid the metal coating on the water quality caused by direct contamination.
4. does not scale: do not clean up the scale, heat-absorbing effect over a decade.
5. not bombing: Even in 300 degree heat, they will not be bombing.

LiYang-E Unpressurized Solar Water Heater

1)ce&solarkeymark&ccc for solar collector
2)15 years warranty
3)easy installation, adjustable bracket
4)Best price with hi

LiYang Solar Water Heater:

Automatic water with only the back; open directly out of hot water;
water booster anti Xiere; free so warm at any time by;
save thousand Yuan equipment costs; three more into hot water; Y
in Ching-proof anti-dry; winter Summer wind blocking antifreeze;
without water worries can be emergency; simple, reliable and energy saving.

1.1. double endothermic heat Unlimited: Two hot three-high purple tube, a three-target magnetron sputtering process, the uniformity of film coverage, high temperature aging does not fall off; double endothermic design, firmly locked One heat, heat enough power, thermal infinite; borosilicate glass 3.3, super compressive strength, resistance to rain and hail, sustainable use is not damaged; high temperature for a long vacuum tube, heat is not lost.
2.2. Thermal 1 +1, temperature, eternal security: electric heating water tank reserved for the interface to meet your diverse water needs; 1 +1 complementarity of solar and electrical energy, energy saving, heat is greater; out of the climate alone limits of solar , You can always enjoy the hot water.
3.3. hot water that is produced is used: pipeline is not in storage, the winter ice-free tube, water is more power; twisted the faucet, you can use hot water, bathing, washing, laundry, washing fruits and arbitrary.
High borosilicate all-glass vacuum tube 3.3; Tsinghua patented technology; ISo9002quality certification
solar vacuum tube
scaffold
tank
length
diameter
angle
case material
insulation material
liner material
capacity
1800mm
58mm
45
Imports of high quality stainless steel bend frame
Imports of stainless steel
55mm-65mm imported polyurethane foam
SUS304-2B imported food grade stainless steel plate
180L

Lifepo4 battery packs 24V36V48V for Electric vehicles

Lifepo4 battery packs 24V36V48V for Electric vehicles
1.Lifepo4 battery
2.High energy density
3.long cycle life
Lifepo4 battery packs 24V36V48V for Electric vehicles
No.
Model
Nominal voltage
Nominal capacity
Dimensions
Weight of battery pack
Standard charger
Including BMS and out case
Including BMS and out case
(V)
(Ah)
L*W*H (mm)
(kg)
(A)
1
GEB-LFP24V8AH-1
24V
8Ah
110*75*378
4.2KG
1.8A
2
GEB-LFP24V8AH-2
24V
8AH
89*86*401
4.2KG
1.8A
3
GEB-LFP24V10AH-1
24V
10Ah
110*75*378
4.5KG
2A
4
GEB-LiMn24V10AH
24V
10Ah
89*89*401
4.5KG
2A
5
GEB-LFP36V8AH
36V
8Ah
110*75*378
4.45KG
2A
6
GEB-LFP36V10AH-1
36V
10Ah
149*56*370
5.05KG
2A
7
GEB-LFP36V10AH-2
36V
10Ah
71*152*328
6KG
2A
8
GEB-LFP48V10AH
48V
10Ah
150*140*150
7KG
2A
9
GEB-LFP48V20AH
48V
10Ah
300*140*150
14.5KG
4A

Light for Garden Led Solar

light for garden
1.CE,ISO9001,ROHS Approved
2.100,000 hours working time
3.80% energy saving
4.Pollution-free
light for garden

Standing 7 feet tall, the Gama Sonic Single Solar Lamp Post is just what you need to add elegant lighting to your home's exterior. You'll love the easy operation of this beautiful solar lamppost: it automatically turns on at dusk and off at dawn, or you can alternatively choose to use the manual on/off switch. Six super-bright LED lights use a specially patented cone reflector to make the light brighter. The 19th-century gaslight design features beveled glass and classic appeal to your front or back yard.

Light wedge

The high-quality product was made in China with Siemens technology and USA boiler .Superior quality and expensive !
LED Panel Light
Easily use

Easily installation or replacement by users
Do not need regular replacement or maintenance
Elegant design

Super slim design, less than 10mm thickness.
Fashion and good looking, provide users with exceptional versatility.
Energy-efficiency

More than 50,000 hour lifespan, consuming less power and providing more light than traditional lighting products.
50% power saving, over 3 times of lifetime longer than the commonly-used T8 lighting fixtures.
Eco-friendly

High brightness, low light dissipation and no glare
Designed to contain no hazardous chemicals, such as mercury, or harmful radiation emissions such as UV or IR.

Applications

Baihaihui panel light can be recessed or hung, placed on ceilings or walls. It provides a multitude of benefits for working in studio, or anywhere in the world.
Large field: Factory, Parking lot, Gas station, or Sport field
General space: Office, Meeting room, Classroom or Studio
Limited space: Elevator, Closet, Cabinets
The environment of long time lighting: Bank, Convenient store
Lower ambient temperature needed: Freezer, Refrigerator
High degree of cleanliness required: Clean lab, Medical treatment, Food industry
Place prevented form heat and UV radiation: Jewelry shop, Art gallery, Museum

Specification

Model
40W series

Optical Performance
Color Temperature
6000, 4000, 3000°K
(+/-300°K)
Luminous Flux
2450 lm
Uniformity
75 %
Dimension
Configuration Dimension(L × W × H)
601× 601× 9.7 mm
Visible Area Dimension (L × W )
565 × 565 mm
Weight (Without Power)
3.5 kg
Electronic Control Gear
Input Voltage(AC)
100~240 V (50/60 Hz)
Power Consumption
38 W
Lifetime
30,000Hrs

Lighting fire cotton

Lighting fire cotton
Specs:2mm
Lighting fire cotton
This product is made with a special formula finishing, fire prevention, expanding the limits of 250 degrees, expansion of multiples of 200-300 for lighting and fire doors, windows from the fire, blocking breathing, sealing purposes. In line with EU environmental directives.

Lignite Briquetting Plant,Iron Scale Press,Middle Coal Briquette Machine

Our Lignite Briquetting Plant,Iron Scale Press,Middle Coal Briquette Machine can supply higher pressure and higher density
Our Lignite Briquetting Plant,Iron Scale Press,Middle Coal Briquette Machine can supply higher pressure and higher density during production of briquettes.Our Lignite Briquetting Plant,Iron Scale Press,Middle Coal Briquette Machine can supply higher pressure and higher density mainly used in the briquettes making of various color and black metallic mine powder. It is applicable to make briquettes from Iron scale, iron sludge,Precipitator dust, Iron concentrate, Raw material powder,Manganese ore fines,Silicomanganese alloy,Coal powder, coke powder, slime peat, middle coal,lignite, Charcoal powder, fireproof material, Desulfurized gypsum,Dolomite etc.
Our Lignite Briquetting Plant,Iron Scale Press,Middle Coal Briquette Machine has two larger rollers in a fixed position in the frame, the other two smaller rollers are moveable. As its named implied, it has four rollers and do twice pressing in production of briquettes, so the briquette is stronger and in higher density, the surface of briquettes is smoother.
Our Lignite Briquetting Plant,Iron Scale Press,Middle Coal Briquette Machine is national patent product in China.

Liquid Nitrogen Unit

Jereh nitrogen pumper used for liquid nitrogen fracture.
LN2 Vaporizer ADFV-1000
Discharge pressure 10,000psi@650K CFH
·The main components of this truck mounted nitrogen pumper are adopted the first class quality products to ensure the steady performance and advanced technologies of the Unit. They are ACD Nitrogen Plunger Pump & Boost Pump, Cryoquip Advanced Diesel Fired Nitrogen Vaporizer, MTU/DDC Engine, Allison Transmission, Autoclave Cryogenic High Pressure Tubing and Valve,etc.
·The ADFV nitrogen vaporizer incorporates advanced burner design technology combining technologies of both burner air distribution and furnace temperature control. Each of the eight burners operates independently providing for more reliability and efficient nitrogen temperature control.
·The nitrogen coil discharge temperature is monitored by the control system and automatically cycles the burners as necessary, managing the nitrogen discharge temperature. Combustion air temperature entering the coil is monitored and will automatically trim burners to prevent over temperature of the process coil. Bluetooth communications is available.
·ADVF nitrogen vaporizer features safety operation and reliable ignition. The nitrogen discharge temperature is automatically controlled and adjusted in full range flow rate of high pressure pump.
·The unit is equipped with JR advanced wireless data acquisition system to real-time detect and record the pressure, Nitrogen discharge flow rate and temperature and burner temperature, etc.
·A standing pilot igniting control system is provided for quick response and no need for propane.
·Fan speed automatic control system keeps the fan speed invariable when the engine speed changes and requires no additional hydraulic power pack.
·The unit is equipped with operator's control cabin.

Chassis
VOLVO 6×4
Deck Engine
DDC 12V2000AT
Deck Transmission
Allison S8610M
LN2 Triplex pump
ACD
LN2 Vaporizer
ADFV-1000
LN2 boost pump
ACD
Max. GN discharge pressure
15,000psi
Max. gaseous nitrogen discharge flow
650,000SCFH@2''
Discharge pressure @ Max. flow
10,000psi@650K CFH
Weight
24000kg
Overall dimensions
10500×2500×4000mm

2011 DYAN Improved Environment-friendly Biomass Briquetting Press Machine

Wood Briquette Machine:
1.High production, energy-saving
2.Long durablity,good output
3.Easy to operate
4.Stable performance
2011 DYAN Improved Environment-friendly Biomass Briquetting Press Machine

Biomass Briquette Machine
make the biomass material into briquettes. After the well preparement of raw metarial, briquetting is easy at right operation of biomass briquette press. When machine rise to over 300 centigrade, the material can be feeding continuously into briquetting press. First, the color of briquettes may be a little dark even black, but after a while, the color will be light to normal level coming out of biomass briquette machine.
Appropriate Biomass Residues for Briquetting:

1. Effect of particle size and shape of the agro residues for densification. The ideal size was identified to be 3-5mm.
2. Effect of moisture. Ideal level was 8 to 12 per cent.
3. Effect of feed preheating studied and the temperature upto 90 to 110 degree centigrade for the feed was optimised.
4. Effect of temperature on the die was found important and the temperature at 280 to 290 0C was observed to be most appropriate
5. Effect of mixing rice husk with bagasse and bagasse pith to achieve the briquetting of these materials

Working Principle of Sawdust Briquette Machine:

Sawdust Briquette machine uses a large screw to grind, compress and extrude the biomass into briquettes. The natural lignin content in biomass is liberated with wood fiber under high pressure and temperature.In the briquetting process lignin serves as the glue and combines the particles of wood together,thus binding, compressing the biomass to form into various moulds of high density briquette, such as hexagonal,quadrangular, square,etc. As your requirement, we can also change the shape to order. And the diameter of briquettes are from 50-80 mm. Moreover non-binder needs to be used during this process.
The process for producing charcoal briquette as follow:

1. Crush the raw material into small pieces (diameter is about 3-5mm)
2. Dry the material by machine or dried it in the sun , till the moisture is less than 12%
3. Put the material into feed let of briquette machine
4. Produce the briquette stick from biomass material without any additive
4. Carbonized the briquette stick
Characteristic of Biomass Briquette Machine:

1. No binder or noxious chemical need to use.
2. The humidity of the raw materials is controlled in 8-12%.
3. Using the advanced Hot air drying system with the perfect performance.
4. After the processing of High temperature, purification, smoke removing, the carbonizing equipment transforms the semi-finished bio-fuel briquette into a smoke-free, tasteless, non-toxic cleaning carbon.

Advantages of biomass briquettes:
♦ Increase the net calorific value per unit volume after biomass briquetting
♦ Easy to transport and store as densified product
♦ Better solution to the problem of residue disposal
♦Uniform in size and quality as a kind of biofuel briquette
♦ Reduce excess deforestation by providing a substitute for fuel wood

Biomass Briquette Machine:

Lithium Battery

1.Lithium Battery
2.Second Battery
3.Capacity:50Ah
4.Long cycle life
The Lithium Battery is belonging to the LiFePO4 serie or the Second Battery.It has many advantages,such as high density,weight light,environmental.Following is the paremeter:

Lithium battery pack

Long cycle life (500-1000times)
More safety (superior braded system)
No pollution (battery material exist no toxic substan

Battery module parameters


Model
Parameters
Battery style
LiFePO4
Shell material
Nickel plating steel shell
Working Voltage
3.2V
Nominal capacity
3000mAh
Weight
About 83g
Battery size
H:65.5±0.5mm D:26.1±0.2mm
resistance
≤30 mΩ
Charging limit voltage
3.65V
Discharging limit voltage
2.0V
Normal working current
3Ah
Max continuous discharge current
9Ah
Maximum pulse current
15Ah
Quality Energy density
120wh/kg
Volume Energy density
280wh/L
mass power density
500W/kg
Charging working temperature
0--45°C
Discharge working temperature
-20--60°C
Storage temperature
Short term(1month)-20-45°C Long term:(1 year)-20-2545°C
Cycle life
0.5C 100%DOD>2000
Outer packing
PVC/PET
Protect function
Inside PTC (can select0



Rate discharge curve

•Advantage:
•Long cycle life (500-1000times)
•More safety (superior braded system)
•No pollution (battery material exist no toxic substance)

Lithium battery pack

Long cycle life (500-1000times)
More safety (superior braded system)
No pollution (battery material exist no toxic substan

Battery module parameters


Model
Parameters
Battery style
LiFePO4
Shell material
Nickel plating steel shell
Working Voltage
3.2V
Nominal capacity
3000mAh
Weight
About 83g
Battery size
H:65.5±0.5mm D:26.1±0.2mm
resistance
≤30 mΩ
Charging limit voltage
3.65V
Discharging limit voltage
2.0V
Normal working current
3Ah
Max continuous discharge current
9Ah
Maximum pulse current
15Ah
Quality Energy density
120wh/kg
Volume Energy density
280wh/L
mass power density
500W/kg
Charging working temperature
0--45°C
Discharge working temperature
-20--60°C
Storage temperature
Short term(1month)-20-45°C Long term:(1 year)-20-2545°C
Cycle life
0.5C 100%DOD>2000
Outer packing
PVC/PET
Protect function
Inside PTC (can select0



Rate discharge curve

•Advantage:
•Long cycle life (500-1000times)
•More safety (superior braded system)
•No pollution (battery material exist no toxic substance)

Lithium-iron Car battery

1,save 5% oil
2,fast start-up performance
3,long cycle life 6-8years.
4.hight discharge rate ability
Hipower LifePO4 battery common Features:


High Performance

- Provides a High Theoretical capacity of 170mah/g and a High Practical capacity as high as 165mah/g.
Extremely Safe/Stable Chemistry

- High intrinsic safety, non-explosive & will not catch fire under collision, due to over-charging, or from a short circuit. High thermal stability of phases up to 500C.
High Discharge Rate Capability
- Among the best for all high power output demands
Extraordinary Long Cycle Life: 5-7 years

- Achieves up to 2000 cycles per life-over 7 times the life of Lead Acid and 3 times of NIMH and 3-4Times of LI-ION, LI-MN battery
Environmentall Friendly
- Non-toxic, non-contaminating-no rare metals, UL, CE, SGS/ROHS approved
Wide working temperature range
- From -45C – +70C (Extremely cold and extremely hot weather will not affect its performance)
Flexible Form Factor

- Small in size and light in weight, 1/3 weight of Lead Acid and 65% weight of NIMH. 2/3 size of Lead Acid.

Lithiumion battery Led film 8GB trail night vision hunting video camera

1.2.5TFT Zoom in/out Multi-shot1-9pics
2.With laser light&optical filter
3.54LED lights Trigger time1-2Secs
4.10mega
5.8GB
Lithiumion battery Led film 8GB trail night vision hunting video camera


Specifications
Image sensor
CMOS sensor
Pixel
10 MP 8MP,5MP,3MP,adjustable
Still image
2520*1920(5MP);3054*2336(8MP);3648*2736(10MP)
Video resolution
320*240 640*480
File format
JPG/AVI
Display
2.5" TFT - LCD
External memory
SD/MMC card up to 8GB
Internal memory
16MB of built-in memory
Exposure
Auto
Low battery
Auto indicator(yellow light)
Card full display
Auto
Playback Mode
Televishon or computer play
TV-out
NTSC or PAL
PIR distance
Adjustable
OS
WINDOWS98/98SE/ME/2000/XP
Power supply
Rechargeable lithium-ion battery or 9-12V DC input
Operating Temperature
-4 3/4 F to 122 3/4 degrees F
Storage Temperature
-22 3/4 F to 167 3/4 degrees F


Main Feature
1. Mode LCD displays date, time,picture,number,delay time, and battery status.
2..Motion triggered and adjustable PIR sensitivity
3. Auto-distinguish images. Color images in daytime/black&white night iamges
4.Stores pictures in SD/MMC card
5.Multi-shot of 1/3 pictures
6.Video default is 30 seconds
7.Programmable from 10 seconds to 990 seconds delay time between triggers
8."NO Flash" Uses 54 infrared LEDS to illuminate the coverage area
9.Water proof housing case
10.Four Native Languages: German, French, English, Chinese
11.Date and time stamp on each picture
12.Power jack for external DC 9-12V input

Application of hunting camera
1.For hunting ,automatically to take pictures of wild animals
2.Home security evidence
3.Office of the anti-theft evidence
4.Small and medium sized supermarket security evidence
5.Other special occasions automatic shooting evidence

Each Package Includes
Digital camera with all weather housing:1 pcs
Rechargeable Lithium battery:1 pcs
AC 110-240V Charger:1 pcs
USB cable:1 pcs
A/V cable:1 pcs
Manual:1 pcs
Strap:1 pcs
CD:1 pcs
Does not include SD card

Long Sevice Life Biocoal Forming Machine for Biomass Briquettes

Biocoal Forming Machine:
1.High production
2.Long durablity
3.Easy to operate
4.Stable performance
Sawdust Briquette Machine
make the biomass material into briquettes. After the well preparement of raw metarial, briquetting is easy at right operation of biomass briquette press. When machine rise to over 300 centigrade, the material can be feeding continuously into briquetting press. First, the color of briquettes may be a little dark even black, but after a while, the color will be light to normal level coming out of biomass briquette machine.
Appropriate Biomass Residues for Briquetting:

1. Effect of particle size and shape of the agro residues for densification. The ideal size was identified to be 3-5mm.
2. Effect of moisture. Ideal level was 8 to 12 per cent.
3. Effect of feed preheating studied and the temperature upto 90 to 110 degree centigrade for the feed was optimised.
4. Effect of temperature on the die was found important and the temperature at 280 to 290 0C was observed to be most appropriate
5. Effect of mixing rice husk with bagasse and bagasse pith to achieve the briquetting of these materials

Working Principle of Sawdust Briquette Machine:

Sawdust Briquette machine uses a large screw to grind, compress and extrude the biomass into briquettes. The natural lignin content in biomass is liberated with wood fiber under high pressure and temperature.In the briquetting process lignin serves as the glue and combines the particles of wood together,thus binding, compressing the biomass to form into various moulds of high density briquette, such as hexagonal,quadrangular, square,etc. As your requirement, we can also change the shape to order. And the diameter of briquettes are from 50-80 mm. Moreover non-binder needs to be used during this process.
The process for producing charcoal briquette as follow:

1. Crush the raw material into small pieces (diameter is about 3-5mm)
2. Dry the material by machine or dried it in the sun , till the moisture is less than 12%
3. Put the material into feed let of briquette machine
4. Produce the briquette stick from biomass material without any additive
4. Carbonized the briquette stick
Characteristic of Biomass Briquette Machine:

1. No binder or noxious chemical need to use.
2. The humidity of the raw materials is controlled in 8-12%.
3. Using the advanced Hot air drying system with the perfect performance.
4. After the processing of High temperature, purification, smoke removing, the carbonizing equipment transforms the semi-finished bio-fuel briquette into a smoke-free, tasteless, non-toxic cleaning carbon.

Advantages of biomass briquettes:
♦ Increase the net calorific value per unit volume after biomass briquetting
♦ Easy to transport and store as densified product
♦ Better solution to the problem of residue disposal
♦Uniform in size and quality as a kind of biofuel briquette
♦ Reduce excess deforestation by providing a substitute for fuel wood

Biomass briquette machine:


briquette forming machine,biomass briquette machine,charcoal briquette machine

Long and adjustable handle 18&quot; 24&quot; 36&quot; versatile wire clipper blade

Long handle /adjustable handle /18" 24" 36" versatile wire clipper blade.
Wire clipper blade
Ordernumber
Name
10820
Blade of long handle gear wire clipper
10821
Blade of adjustable handle gear wire clipper
10822
Blade of 18
"
versatile wire clipper
10823
Blade of 24" versatile wire clipper
10824
Blade of 36" versatile wire clipper

Long burning time biomass briquette machine

Biocoal Forming Machine:
1.High production
2.Long durablity
3.Easy to operate
4.Stable performance
Sawdust Briquette Machine
make the biomass material into briquettes. After the well preparement of raw metarial, briquetting is easy at right operation of biomass briquette press. When machine rise to over 300 centigrade, the material can be feeding continuously into briquetting press. First, the color of briquettes may be a little dark even black, but after a while, the color will be light to normal level coming out of biomass briquette machine.
Appropriate Biomass Residues for Briquetting:

1. Effect of particle size and shape of the agro residues for densification. The ideal size was identified to be 3-5mm.
2. Effect of moisture. Ideal level was 8 to 12 per cent.
3. Effect of feed preheating studied and the temperature upto 90 to 110 degree centigrade for the feed was optimised.
4. Effect of temperature on the die was found important and the temperature at 280 to 290 0C was observed to be most appropriate
5. Effect of mixing rice husk with bagasse and bagasse pith to achieve the briquetting of these materials

Working Principle of Sawdust Briquette Machine:

Sawdust Briquette machine uses a large screw to grind, compress and extrude the biomass into briquettes. The natural lignin content in biomass is liberated with wood fiber under high pressure and temperature.In the briquetting process lignin serves as the glue and combines the particles of wood together,thus binding, compressing the biomass to form into various moulds of high density briquette, such as hexagonal,quadrangular, square,etc. As your requirement, we can also change the shape to order. And the diameter of briquettes are from 50-80 mm. Moreover non-binder needs to be used during this process.
The process for producing charcoal briquette as follow:

1. Crush the raw material into small pieces (diameter is about 3-5mm)
2. Dry the material by machine or dried it in the sun , till the moisture is less than 12%
3. Put the material into feed let of briquette machine
4. Produce the briquette stick from biomass material without any additive
4. Carbonized the briquette stick

Characteristic of Biomass Briquette Machine:

1. No binder or noxious chemical need to use.
2. The humidity of the raw materials is controlled in 8-12%.
3. Using the advanced Hot air drying system with the perfect performance.
4. After the processing of High temperature, purification, smoke removing, the carbonizing equipment transforms the semi-finished bio-fuel briquette into a smoke-free, tasteless, non-toxic cleaning carbon.

Advantages of biomass briquettes:
♦ Increase the net calorific value per unit volume after biomass briquetting
♦ Easy to transport and store as densified product
♦ Better solution to the problem of residue disposal
♦Uniform in size and quality as a kind of biofuel briquette
♦ Reduce excess deforestation by providing a substitute for fuel wood

Biomass briquette machine:

briquette forming machine,biomass briquette machine,charcoal briquette machine

Low - consumption and Energy- saving Coal Ball press machine

Coal Ball Press Machine
1. Output: 4T/H
2. Power: 7.5KW
3. Machine weight: 1.4T

Coal Ball Press Machine

Introduction:
Our factory can provide you single machine and complete set of equipment.
The finished products are egg-shaped ball, oval-shaped ball, circular-shaped ball, square-shaped ball, columnar-shaped ball, banding-shape ball, cake-shaped ball, etc. Furthermore, apart from shapes mentioned above, we can also produce other various types based on customer requirements. Ball press is widely used in metallurgy, mining, coal, refractories, abrasive, fertilizer, ceramics, etc.

Specification:
It is widely applied to produce powdered coal and fine coke balls,powdered coal bar of fertilizer industry,applicable to mineral ball of chemical industry, applicable to mineral fines of different kinds of ferrous and non-ferroud metal,applicable to iron scale and dust elimination of metallurgy and applied to produce balls of sludge and refractories.

Main technology parameter:
Type
Output (T/H)
Annual output (10000T)
Power (kw)
1500
50
15
185
1300
40
12
160
1200
35
10
132
1000
25
7
90
800
20
5
55
750
17
4
45
650
14
3.5
37
600
12
3
30
500
10
2.5
22
450
8
2
18.5




Welcome to Zhengzhou Dayang Briquette Equipment Co,. Ltd.

Low Energy Consumption wood charcoal briquette making machine

Biocoal Forming Machine:
1.High production
2.Long durablity
3.Easy to operate
4.Stable performance
Sawdust Briquette Machine
make the biomass material into briquettes. After the well preparement of raw metarial, briquetting is easy at right operation of biomass briquette press. When machine rise to over 300 centigrade, the material can be feeding continuously into briquetting press. First, the color of briquettes may be a little dark even black, but after a while, the color will be light to normal level coming out of biomass briquette machine.
Appropriate Biomass Residues for Briquetting:

1. Effect of particle size and shape of the agro residues for densification. The ideal size was identified to be 3-5mm.
2. Effect of moisture. Ideal level was 8 to 12 per cent.
3. Effect of feed preheating studied and the temperature upto 90 to 110 degree centigrade for the feed was optimised.
4. Effect of temperature on the die was found important and the temperature at 280 to 290 0C was observed to be most appropriate
5. Effect of mixing rice husk with bagasse and bagasse pith to achieve the briquetting of these materials

Working Principle of Sawdust Briquette Machine:

Sawdust Briquette machine uses a large screw to grind, compress and extrude the biomass into briquettes. The natural lignin content in biomass is liberated with wood fiber under high pressure and temperature.In the briquetting process lignin serves as the glue and combines the particles of wood together,thus binding, compressing the biomass to form into various moulds of high density briquette, such as hexagonal,quadrangular, square,etc. As your requirement, we can also change the shape to order. And the diameter of briquettes are from 50-80 mm. Moreover non-binder needs to be used during this process.
The process for producing charcoal briquette as follow:

1. Crush the raw material into small pieces (diameter is about 3-5mm)
2. Dry the material by machine or dried it in the sun , till the moisture is less than 12%
3. Put the material into feed let of briquette machine
4. Produce the briquette stick from biomass material without any additive
4. Carbonized the briquette stick
Characteristic of Biomass Briquette Machine:

1. No binder or noxious chemical need to use.
2. The humidity of the raw materials is controlled in 8-12%.
3. Using the advanced Hot air drying system with the perfect performance.
4. After the processing of High temperature, purification, smoke removing, the carbonizing equipment transforms the semi-finished bio-fuel briquette into a smoke-free, tasteless, non-toxic cleaning carbon.

Advantages of biomass briquettes:
♦ Increase the net calorific value per unit volume after biomass briquetting
♦ Easy to transport and store as densified product
♦ Better solution to the problem of residue disposal
♦Uniform in size and quality as a kind of biofuel briquette
♦ Reduce excess deforestation by providing a substitute for fuel wood

Biomass briquette machine:


briquette forming machine,biomass briquette machine,charcoal briquette machine

2011 DYAN Professional Screw Type Biomass Briquette Machine

Wood Briquette Machine:
1.High production, energy-saving
2.Long durablity,good output
3.Easy to operate
4.Stable performance
2011 DYAN Professional Screw Type Biomass Briquette Machine

Biomass Briquette Machine
make the biomass material into briquettes. After the well preparement of raw metarial, briquetting is easy at right operation of biomass briquette press. When machine rise to over 300 centigrade, the material can be feeding continuously into briquetting press. First, the color of briquettes may be a little dark even black, but after a while, the color will be light to normal level coming out of biomass briquette machine.
Appropriate Biomass Residues for Briquetting:

1. Effect of particle size and shape of the agro residues for densification. The ideal size was identified to be 3-5mm.
2. Effect of moisture. Ideal level was 8 to 12 per cent.
3. Effect of feed preheating studied and the temperature upto 90 to 110 degree centigrade for the feed was optimised.
4. Effect of temperature on the die was found important and the temperature at 280 to 290 0C was observed to be most appropriate
5. Effect of mixing rice husk with bagasse and bagasse pith to achieve the briquetting of these materials

Working Principle of Sawdust Briquette Machine:

Sawdust Briquette machine uses a large screw to grind, compress and extrude the biomass into briquettes. The natural lignin content in biomass is liberated with wood fiber under high pressure and temperature.In the briquetting process lignin serves as the glue and combines the particles of wood together,thus binding, compressing the biomass to form into various moulds of high density briquette, such as hexagonal,quadrangular, square,etc. As your requirement, we can also change the shape to order. And the diameter of briquettes are from 50-80 mm. Moreover non-binder needs to be used during this process.
The process for producing charcoal briquette as follow:

1. Crush the raw material into small pieces (diameter is about 3-5mm)
2. Dry the material by machine or dried it in the sun , till the moisture is less than 12%
3. Put the material into feed let of briquette machine
4. Produce the briquette stick from biomass material without any additive
4. Carbonized the briquette stick
Characteristic of Biomass Briquette Machine:

1. No binder or noxious chemical need to use.
2. The humidity of the raw materials is controlled in 8-12%.
3. Using the advanced Hot air drying system with the perfect performance.
4. After the processing of High temperature, purification, smoke removing, the carbonizing equipment transforms the semi-finished bio-fuel briquette into a smoke-free, tasteless, non-toxic cleaning carbon.

Advantages of biomass briquettes:
♦ Increase the net calorific value per unit volume after biomass briquetting
♦ Easy to transport and store as densified product
♦ Better solution to the problem of residue disposal
♦Uniform in size and quality as a kind of biofuel briquette
♦ Reduce excess deforestation by providing a substitute for fuel wood

Biomass Briquette Machine:

Low Noise Carbonized Furnace

1.High efficiency
2.Stable performance
3.Competitive price
4.Easy operation
Carbonized Furnace
Our carbonizing furnace is ideal equipment for wood briquettes to have anoxic distillation carbonization. Adopting reasonable structure, the carbonizing furnace needs small quantity of heat consumption only. And the most important is that our carbonizing furnace is equipped with Superheated Stream cooling system, thus can speed up the cooling process, improve the quality of charcoal and shorten the production cycling time to 24-48 hours with the features of easy operation, higher safety, high efficiency and energy saving. The final products charcoal briquette bars can be used for heating furnace, industrial boilers, biomass power plant, barbecue and so on.


Main data
:
Model: carbonization furnace THL-3
Power: 4 kw
Capacity: 3 cubic meters
Working cycle: 3-4 days
Weight: 4000/4500 kg
Pack size: 2.55*1.82*2.1 m


We are one of the biggest manufacturers in China. Our machines have exported. If you are interested in our products, please be free to consult with us at any time.

Carbonized Furnace internal


Finished products from carbon bar furnace

Low Noise Hammer Mill

1.Reasonble price
2.Excellent quality
3.Low investment and energy consumption
4.Stable performance
Hammer Mill
Hammer mill is the most ideal milling equipment of all kinds of wood piece, straw, grass, stalk, tree branches, waste cardboard, bamboo, wood scraps, coconut shell, corn stalk, peanut shell, wheat stalk, wood fuel, cotton stalk, biomass shell and so on. This kind of hammer mill is widely used in foddor factory, Swine farm, wood factory, etc. Hammer mill is equipped with high carbon steel blade. The raw materials can be crushed into straw particles, whose diameter is 3-5 mm. The durable hammer mill works with high efficiency and gains more good reputation from European users.

main data:
Model
HM-I
HM-II
HM-III
HM-IV
HM-V
Power (kw)
4kw3phase
7.5kw3phase
11 kw, 3 phase
18.5 kw, 3 phase
22 kw, 3 phase
Capacity(kg/h)
100-300
400-500
500-600
700-800
900-1000
Diameter of raw material(mm)
Less than 50
Less than 50
Less than 50
Less than 50
Less than 50
Diameter,of,crushed,materials(mm)
3-5
3-5
3-5
3-5
1-3
Noise(DB)
Less than 60
Less than 60
Less than 60
Less than 60
Less than 60
Motor turning speed(R/min)
2600
2600
2600
2600
2600
Weight(kg)
250/300
350/400
400/450
490/560
510/580
Pack size(m)
1.3*1*0.8
1.4*1.2*1.2
1.5*1.2*1.5
1.66*1.2*1.77
1.72*1.3*1.83


We are one of the biggest manufacturers in China. Our machines have exported. If you are interested in our products, please be free to consult with us at any time.

Hammer


Final product

Low Power ZigBee Module

Low Power ZigBee Module
Part number: HT-Z-EM-MDL-2400-001-C-V1.0.0
Core chip: EM250
Antenna: PCB Antenna
Low TX Power ZigBee Module
Part number: HT-Z-EM-MDL-2400-001-C-V1.0.0
Core chip: EM250
Antenna: PCB Antenna
RF output power: Max 1mW
RF receive sensitivity: Min -92dBm
Point-to-point communication distance: 180m (view of sight)
Power consumption:
- RX mode:36 mA
- TX mode: 36mA
- Hibernate mode: 5uA

Low Price 135 W ac dc charger for Dell PA-13 from fcatory

ac dc charger for Dell
green power safe, compatible
CE/FCC/RoHS certificated
12 months warranty
fast delivery


19.5 V 6.7 A notebook ac adapter
for Dell PA-13 notebook


135 W ac dc charger
2. Specifics:
Output :
19.5 V 6.7 A
Power :
135 W
Tip :
7.4*5.0 mm
Input:
100 V— 240 V
Input Frequency:
47-63 Hz
Efficiency :
> 87 %
Ripple Noise:
< 400mVp-p
Warranty:
12 months
M.T.B.F:
50000 Hours
Certification:
CE / FCC / RoHS




Input
100—240V
OverCurrent protection
Yes
Efficiency
> 87 %
Output

19.5 V
6.7 A
OverHeat Protection
Yes
Ripple Noise
< 400mVp-p
Warranty
12 months
OverVoltage protection
Yes
DC tip
5.0 * 7.4 mm
M.T.B.F
50000 Hours
ShourCircuit Protection
Yes
Size
155*55*30mm

Compatible Part numbers:
P/N 09Y819,PA-1131-02D,X7329,K-5294,HP-AD130B13P,D5A,W1828,P/N T5322,NADP-130AB,NADP-130AB B,NADP-130AB D,W1828,310-4180,D1078,TC887,D1078,301-6580,310-8275,310-7848,310-7489,ADP-15150,IM-M150727
Compatible with following Series:
Dell Inspiron Notebooks:
5150, 5160, 9300
Dell XPS:
M1210, M170, M1710,M1750,M90,GEN 2,M6300
1.Features:
1. low DC ripple, safe, reliable and stable;
4. Tested by full load high temperature burn-in and 100% aging, low defect rate;
8. CE/FCC/RoHS-certified, environment-friendly and safe.









Aging Test Centre

Low Price Solar Garden Lights

solar garden lights
1.CE,ISO9001,ROHS Approved
2.100,000 hours working time
3.80% energy saving
4.Pollution-free
solar garden lights

Standing 7 feet tall, the Gama Sonic Single Solar Lamp Post is just what you need to add elegant lighting to your home's exterior. You'll love the easy operation of this beautiful solar lamppost: it automatically turns on at dusk and off at dawn, or you can alternatively choose to use the manual on/off switch. Six super-bright LED lights use a specially patented cone reflector to make the light brighter. The 19th-century gaslight design features beveled glass and classic appeal to your front or back yard.